Leviton Switch VZI06-1L Bedienungsanleitung PDF herunterladen

Single Pole (One location) or 3-Way (Multi-location)

Incandescent Dimmer

Cat. No. VZI

6-1L, 600W (Lighted)

120VAC, 60Hz

INSTALLATION INSTRUCTIONS

Single-Pole Wiring Application:

DI-000-VZI06-02A

Tools needed to install your Dimmer:

Slotted/Phillips Screwdriver Electrical Tape

Pliers Pencil

Cutters Ruler

Changing the color of your Dimmer:

Your Dimmer may include three color options. The Dimmer ships

with the White frame attached. To change color of frame, proceed

as follows:

Installing Dimmer by itself or with other devices:

If installing Dimmer in a single device application, proceed with the

INSTALLING YOUR DIMMER section. If installing Dimmer in a

multi-device application, proceed as follows:

MULTI-DEVICE APPLICATION:

In multi-dimmer installations, the reduction of the dimmer’s capacity

is required. Refer to the chart for maximum load per dimmer.

INSTALLING YOUR DIMMER

NOTE: Use check boxes when Steps are completed.

WARNING: TO AVOID FIRE, SHOCK, OR DEATH;

TURN OFF POWER at circuit breaker or fuse and test

that power is off before wiring!

Identifying your wiring application (most

common):

NOTE: If the wiring in the wall box does not resemble

any of these configurations, consult a qualified electrician.

Step 2

Step 3

ONOFF

ONOFFONOFF

ONOFF

3-Way

1. Line or Load

(See important

instruction below)

2. Neutral

3. Ground

4. First Traveler – note color

5. Second Traveler – note color

NOTE: For matching remote w/LEDs

installation, the First Traveler becomes

Line Hot.

Step 4a

WIRING DIMMER:

Connect wires per WIRING DIAGRAM as follows:

• Green or bare copper wire in wall box to Green terminal screw.

• Line Hot wall box wire to terminal screw marked "BK".

• Load wall box wire to terminal screw marked "RD".

• Dimmer terminal screw marked "YL/RD" should have Red

insulation label affixed.

NOTE: If insulating label is not affixed to terminal screw marked

"YL/RD", use electrical tape to cover.

• Proceed to Step 5.

Hot (Black)

Neutral (White)

Load

Dimmer

Black

White

Green

Ground

Line

120VAC, 60Hz

YL/RD

Use Terminal for 3-Way or

More Applications Only.

For Single-Pole Applications,

Do Not Remove This Label.

YL/RD

Terminal

Screw marked

Black (BK)

Terminal

Screw marked

Red (RD)

Terminal

Screw marked

Yellow/Red

(YL/RD)

Terminal Label:

Use Terminal for 3-Way or More Applications Only.

For Single-Pole Applications, Do Not Remove This

Label.

Back Wire (either hole may

be used)

Back wire openings use #14-12

AWG

solid copper wire only.

• Make sure that the ends of the wires from the wall box are

straight (cut if necessary).

• Remove insulation from each wire in the wall box as shown.

• For Single-Pole Application, go to Step 4a.

• For 3-Way Coordinating Remote (no LEDs) Application, go

to Step 4b.

• For 3-Way Matching Remote (with LEDs) Application, go to

Step 4c.

WARNINGS AND CAUTIONS:

•To be installed and/or used in accordance with appropriate electrical codes and regulations.

• If you are unsure about any part of these instructions, consult a qualified electrician.

•To avoid overheating and possible damage to this device and other equipment, do not install to control a receptacle, fluorescent lighting, a motor- or a transformer-

operated appliance.

• Use with incandescent or 120V halogen fixtures only.

•Vizia™ dimmers are not compatible with standard 3-way or 4-way switches. They must be used with compatible Vizia™ remotes for multi-location dimming.

• Use only one (1) Vizia™ dimmer in a multi-location circuit with up to 9 coordinating remotes without LEDs or up to 4 matching remotes with LEDs. The remote(s) will

turn the light on at the brightness level selected at the dimmer.

WARNINGS AND CAUTIONS:

• Dimmer may not operate with dioded lamps (Sylvania Designer 16™ or Philips PAR-16™).

•Total minimum load must exceed 40W.

• Dimmer may feel warm to the touch during normal operation.

• Recommended minimum wall box depth is 2-1/2".

• Maximum wire length from dimmer to all installed remotes cannot exceed 300 ft.

• Disconnect power at circuit breaker or fuse when servicing, installing or removing fixture.

• Use this device only with copper or copper clad wire. With aluminum wire use only devices marked CO/ALR or CU/AL.

Single-Pole

1. Line (Hot)

2. Neutral

3. Ground

4. Load

Step 4a cont’d

Strip Gage

(measure bare

wire here or use

gage on back of

the dimmer)

IMPORTANT:

For 3-Way applications, note that one of the screw

terminals from the old switch being removed will usually be a

different color (Black) or labeled Common. Tag that wire with

electrical tape and identify as the common (Line or Load) in both

the dimmer wall box and remote wall box.

5/8"

(1.6 cm)

Step 1

√

Cut

(if necessary)

Side Wire Connection

Side wire terminals accept

#14 AWG

solid copper wire only.

3-Way Wiring with Coordinating Dimming

or Switching Remote (no LEDs)

Step 4b

YL/RD

Terminal

Screw marked

Black (BK)

Terminal

Screw marked

Red (RD)

Terminal

Screw marked

Yellow/Red

(YL/RD)

Coordinating Remote

Dimmer

Step 4b cont’d

WIRING DIMMER:

Connect wires per WIRING DIAGRAM as follows:

NOTE: When using the coordinating remote without LEDs, the dimmer

can be installed on either the Line or Load side of the 3-way circuit.

NOTE: Maximum wire length from dimmer to all installed remotes

cannot exceed 300 ft.

• Green or bare copper wire in wall box to Green terminal screw.

• Line Hot (common) wall box wire identified (tagged) when

removing old switch to terminal screw marked “BK”.

• First Traveler wall box wire to terminal screw marked “RD” (note

wire color). This traveler from the dimmer must go to the

terminal screw on the remote marked “RD”.

• Remove Red insulating label from terminal screw marked

“YL/RD”.

• Second Traveler wall box wire to terminal screw marked “YL/RD”

(note wire color). This traveler from the dimmer must go to the

terminal screw on the remote marked “YL/RD”.

WIRING COORDINATING REMOTE:

Connect wires per WIRING DIAGRAM as follows:

NOTE: Maximum wire length from dimmer to last remote is 300ft.

• Green or bare copper wire in wall box to Green terminal screw.

• Load wall box wire identified (tagged) when removing old switch

to terminal screw marked “BK”.

• First Traveler wall box wire (note color as above) to terminal

screw marked “RD”. This traveler from the remote must go to

the terminal screw on the dimmer marked “RD”.

• Second Traveler wall box wire (note color as above) to terminal

screw marked “YL/RD”. This traveler from the remote must go

to the terminal screw on the dimmer marked “YL/RD”.

• Remote terminal screw marked "WH" should have White

insulationlabel affixed.

NOTE: If insulating label is not affixed to terminal screw marked

"WH", use electrical tape to cover.

• Proceed to Step 5.

Hot (Black)

Neutral (White)

Load

Dimmer

Coordinating Remote (no LEDs)

YL/RD

Black

Do not use for

incandescent

applications.

White

Line

120VAC, 60Hz

Green

Ground

Green

Ground

Push in side at tab

to release

Line up tabs and

press in side to

attach

More than

Cat. No. Single Two Devices 2 Devices

VZI

6 600W 500W 400W

MAXIMUM LOAD PER DIMMER FOR MULTI-DEVICE

Preparing and connecting wires:

This dimmer can be wired using side wire terminal

screws or through backwire openings. Choose

appropriate wire stripping specifications accordingly.

(Coordinating Dimming Remote Depicted)

1 2

Inhaltsverzeichnis

Seite 1 - INSTALLATION INSTRUCTIONS

Single Pole (One location) or 3-Way (Multi-location)Incandescent DimmerCat. No. VZIØ6-1L, 600W (Lighted)120VAC, 60HzINSTALLATION INSTRUCTIONSBl Single

Seite 2 - ADVANCED PROGRAMMING FEATURES

To Program:NOTE: Have a flashlight handy ifthis dimmer controls the only lightsource in the room.1. On the dimmer only, engage theair-gap switch by ge

Kommentare zu diesen Handbüchern

Keine Kommentare

Leviton Switch VZI06-1L Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Nein Leviton Switch VZI06-1L herunter. Leviton Switch VZI06-1L User's Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein Leviton Switch VZI06-1L